niXin removes rust
niXin is a rust-converting emulsion used to protect oxidized metal surfaces. It has a very fast operating time. After about 18-48 hours from application, it can be covered with any kind of acrylic paint, enamels, epoxy, solvents, etc. Surfaces treated with niXin can withstand temperatures up to 90º C, without suffering damage to the film. After the final drying, the color is bright black (it is recommended to apply 3 coats).
Nowadays it’s not longer necessary to rub rusty surfaces with sandpaper or wire brush to remove any traces of rust before applying a regular paint: now simply apply niXin, as supplied – with a brush or by spraying directly on the rusted iron.
Product application
For excessively rusty, dirty or stained oil iron surfaces, it is advisable to effectively remove the thickest scales and exfoliate the rust by mechanical means, with a wire brush or degrease the surfaces with solvents. Apply “niXin” with a brush, roller or spray gun. In a few minutes, the yellow-brown semi-transparent film of 
becomes glossy and turns into a hard black chemical complex.
After 1-2 hours a second layer of can be applied (which already increases the excellent corrosion resistance) and / or, after 12-24 hours, an anticorrosive paint or even better, a layer of anticorrosive paint and a final enamel or solvent based varnish layer. Obviously, niXin blackens quickly and prevents corrosion on iron surfaces without rust, while being inefficient through the paint layers. can also be applied to slightly damp iron surfaces without degrading performance.
Dilution for application with roller or brush:
ready to use or dillute 10-15% with drinking water
Dry time until touch (23°C – 65% U.R.):
20 – 30′ at touch – 4h in depth
Surface temperature:
min 5°c / max 40°C
Relative humidity:
max 80%
Surface humidity:
max 20%
Tool cleaning :
Soap and water
The product can be applied on the following surfaces:
– rusty iron;
– new iron.
The surfaces must be properly prepared following the instructions indicated in the section “PRODUCT APPLICATION”.
Warning!
niXin is a substance intended for ferrous metal and will not be used on painted, treated, galvanized or chromed metal!
During application, the brush should not be soaked in the original plastic container with niXin. The amount of niXin considered necessary for application can be poured each time into another plastic container for use and it is absolutely contraindicated to pour the remaining residue after use back in the original plastic container.
Technical specifications
Appearance: viscous liquid
Initial color: white-yellow semi-transparent
Dry color: glassy black
It is enough to apply with a brush or by spraying directly on the rusty metal, insisting 2-3 times on the more corroded points. In the event that the metal is excessively rusty, or dirty with grease or oil, it is necessary to remove the chips, the weakly anchored metal parts, using a wire brush or degreasing the surface with solvent.
A few minutes after applying the product, the semi-transparent, yellow-brown film becomes shiny, intense black and hardens quickly. Rust interacts with this emulsion, turning into a black chemical compound, very resistant to corrosion, compatible after 18-24 hours after complete drying, with paints, enamels, glazes or any other type of finish, even based on solvents (greases, synthetic oils, alkyd, nitro-alkyd, polyurethane, epoxy substances, products based on chlorine-rubber, etc.).
In situatia metalului curat, fara urme de rugina, convertitorul de rugina ofera o protectie anticoroziva mult mai eficienta decat alte tipuride grund sau vopsea.
In the case of clean metal, without traces of rust, the rust converter offers a much more effective corrosion protection than other types of primer or paint.
Contacts
On the website www.nixin.info you cannot order less than 500ml of niXin.
The transport is made by express courier in 3-7 working days. The transport is FREE!
office[at]nixin.info
Monday to Friday 8:30 am to 6:00 pm
Refund and Returns
For questions using the attached form: